There is usually a plug or harness coming from the rear of your factory radio. That way you know that even if you can't trust the wire color, you can trust the heat-shrink color. You can use this point. 3.Question:What will happen if I connect the 12V battery(+) wire of YATOUR to ACC power (ignition) of my car?

ACC will be your ‘accessories ’ on your ignition, so when you turn the key once your accessories will gain power.

22 removes 'dark cloud' for Uber and Lyft, Fox News' big Arizona call angered Trump camp: NYT. Guangzhou Yatour Electronics Technology Co.,Ltd. ← Older Post When I tried it with power source (not in car), VCC V- to (-) on the power source, ACC V+ to (+) it just blinks once for very short time. Disconnect the cable from the negative battery terminal using an adjustable wrench. You will need to test at the fuse box, cigarette lighter or ignition harness. The ignition switch in a motor vehicle is the main electrical component used by the operator to start, run and turn off the vehicle. AKA: Ground, to the body/frame of the vehicle or (-) of the battery battery.

You might want to buy a lil capacitor though, but there is a fuse capacitor in most radios.

Get your answers by asking now. Your Yatour recognize all 6 folders as CD01 and so on. Order by 2 PM PST for Next Business Day Shipping. Also turn the headlights on and then off. Let’s get started.

Copyright © 2020, Retro Manufacturing, LLC.

This wire energizes vehicle accessories such as the radio when the ignition switch is turned to the "ACC" position. Found one? Press question mark to learn the rest of the keyboard shortcuts, https://www.pcmag.com/encyclopedia/term/53705/vcc. What if I do not know Where/How to connect ACC wire of Yatour YT-M06/YT-M05 BMW4 interface? When you tested for the 12 volt constant and Ignition/Accessory wires you grounded your meter/test light to a metal point in the dash. The Connection with Yatour YT-M06 is ok and the installation corresponds exactly your manual. I'll ask my dad since he's the one that was asking but one of the fellas that replied might be better clued than us :), New comments cannot be posted and votes cannot be cast, Press J to jump to the feed. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.

The ACC wire offers power/electricity only when you insert car key into ignition switch and turn it to the left, The ACC wire needs to be connected to car igniton, The 12V permanent battery wire will always offer power/electricity when the vehicle is turned on or off, The 12v permanent battery wire needs to be connected to car battery.

Connect starter relay wire to the "ST" terminal of the ignition switch. Connect the ignition wire to the "IGN" terminal of the ignition switch. Still have questions? The power lead is usually a thick red wire and stays energized at all times.

Pa. judge grants Trump campaign's observation request, Live: Biden moves closer to reaching 270 votes, Pennsylvania AG on Trump lawsuit: 'We'll win again', Black men drifted from Dems to Trump in record numbers, Trump campaign unleashes wave of suits in key states, Fox News hosts question network's Ariz. call for Biden, Coach cracks down on Tate's 'selfish behavior', Giants trainer may have saved this player's wife's life, ESPN announces 300 layoffs, citing 'disruption' amid virus, California's Prop.

If a user can hardly find out proper car ACC power to connect red ACC wire of Yatour BMW4 interface, he can simply connect our red ACC wire to our 12V + wire instead.

To which fuses can I safely connect to within the passenger fusebox?

One is for constant power and the other is switched with the ignition. and Run positions and voltage should come back.

Most aftermarket head units will use …

Source: I have an electrical engineering degree Website: https://www.pcmag.com/encyclopedia/term/53705/vcc. It saves battery power for when you need to operate vehicle components without engine being on.

Some fuse boxes have “tabs” or spades that provide 12 volts constant as well as Ignition/Accessory voltage. Turn the key off. Thats why it would be best to have a small capacitor.

Connect one voice coil negative to the other voice coil positive. This is the correct wire for Ignition/Accessory (red wire). Some switches may use a different letter or number code, so check with the manufacturer of the switch to properly identify the terminals.

This reply is correct in saying connect to system common or ground because of the VCC - portion.

This is the correct wire for Ignition/Accessory (red wire… VCC is I think ‘vehicle common collector’ so you’ll need to wire this part into earth. Using your meter (set to 12v DC) or test light find a good clean metal point in the dash to secure the ground side of your meter/test light. What is ACC wire- -what is 12V battery permanent wire. When you insert key into ignition switch and turn it to the left you are turning on the ACC circuit. Turn the key back to the On/Acc. Newer Post →. So you’ll want to wire this into an ignition source.

Speaker output wires cannot be connected together.

position, probe and test the wires.

position, probe and test the wires. With the key in the off position, probe and test the wires. It sounds to me as though your car battery needs to be recharged. How To Connect 16 AWG wire to Vehicle For Grounding Power Inverter?

Using your meter (set to 12v DC) or test light find a good clean metal point in the dash to secure the ground side of your meter/test light. If your connecting it in your room to a battery its ok just to connect both yellow and red (from radio) to your battery. Remove the factory radio to access the wiring behind the factory radio. In every folder are 99 MP3-file ... What is ACC wire- -what is 12V battery wire? Take the connected car stereo in one hand and use the other to tuck all of the extra wire back into the dashboard as you set the stereo in its opening. If and when you do charge the battery do not have the radio connected. You can read more about it here if you want to learn more.

The voltage should go away. Then I connect any of the rest to (+), it still just blinks for like millisecond, not shine... Am I doing something wrong, or the controller is faulty? 2.Wire name: 12V battery(+) Color: Yellow. Not all factory radios have a 12 volt constant wire; you may need to go to the fuse box, cigarette lighter or ignition harness. If you need more assistance, contact us. I have this fitted in my car, I connected the vcc+ to the side lights positive power and the vcc- to any ground point. Samsung S20+ Bluetooth audio/Ford sync bluetooth problems? If your connecting it in your room to a battery its ok just to connect both yellow and red (from radio) to your battery. The ACC wire offers power/electricity only when you insert car key into ignition switch and turn it to the left. Be sure to “cap” off any unused speaker outputs separately to insure they do not touch each other or short to any part of the dash.

How can I know whether my BMW is with DSP or not?

Red ACC wire has not been connected to 12V + battery wire yet: Red ACC wire has been hooked up with 12V + battery wire now: Why YT-M06 YT-M05 and YT-M04 are not compatible with 2011 and newer RCD310/RCD500/RCD510 radios on VW/Audi/Skoda/Seat? This wire energizes vehicle accessories such as the radio when the ignition switch is turned to the "ACC" position. Again using your meter (set to 12v DC) or a test light find a good clean metal point in the dash to secure the ground side of your meter/test light. This current generates excess heat, and the range of heat tolerance depends on the components and the size of the conductor--wire--used in the circuit.