1.
8. I gave these a light sand and a couple of coats of clear varnish. 1 - Hands setting disk. You will find the material where the hammers are, underneath the movement as well as at the end of the pendulum leader and around the chime rods.
Bill's Clockworks is open by appointment. Replace the back panel and tighten the screws with the screwdriver if removal of the back panel was necessary to access the hand set knob. Now you need to position your lever microswitch on the clock mechanism, as shown in the photo, so that as the gears for the chimes (not the hours) turn, the switch will close at one point and the open again as it turns. b. Open the access door to the dial and hands of the clock if required.
6. Includes Walldog fasteners, Silent, Continuous Sweep Clock Movements to Make Large Clocks, C-Cell, up to 3/8" Thick Dial Face, Nailess Sawtooth Hangers 2" by 5/16" for hardwood frames - Black Oxide Plated 25 PACK, Rotary Tool 144 Piece Pack - Detail and Finish. One side there is a row of gears which operate some cams which lift the hammers to play the various parts of the tune and another part which lifts all the hammers together to strike the number of hours. https://www.ebay.co.uk/itm/1-4Pc-CNC-stepper-Motor... An old westminster chiming mantle clock: Around $15 - $20. Open the access door to the dial and hands of the clock if required.
Following the instructions which came with the shield I was able to set up the clock fairly quickly, but that got me thinking, if the shield could be used on an arduino mega board then surely all the extra output pins could be used to make something more interesting happen at specified times. https://www.ebay.co.uk/itm/Arduino-Stackable-Pin-H... Stepper motor couplers: To connect the stepper motors to the clock mechanism 5mm x 2mm $3.
Stackable Header Pins: To go between the arduino and the shield so that you have room for your 90 degree header pins. Quartz Tide Only Clock Instructions. . This action will break the internal spring in the movement, and the clock will no longer function. Share it with us!
Try pressing it, and see what it does on your particular clock! Your clock chimes the Westminster melody every 15 minutes. The enclosed screw can be recommended to use only for a hard wooden wall.
You can connect your push button switches to these, mounted in a suitable place on your cabinet so that you can adjust the time and LED colour. repeatedly while a song is playing, will cycle through the entire selection of
Howard Miller Chronometer Instructions. Heavy Duty Mirror and Picture Hanger, 6 inch by Hangman. Each function has its own mainspring and is wound independent of the others This allows you the choice of winding the timekeeping spring only if the sound of the chime and strike aren't desired. However, after that, it works perfectly. automatically change every hour. properly when it first reaches the hour position after being reset. 1. You'll need to drill two small holes about 1.5mm diameter and attach the switch with small machine screws and small washers.
A Instruction Guide. There is. Seiko Chiming Clock Manual with Westminster and Whittington Chimes. The nixie tube board comes with some connectors for external switches to be added for 'Mode', 'Up' and 'Down'. a. the.
3. Some models have packing materials inserted into the back of the clock to Lift one side of the clock gently two inches, then put it down to start the pendulum swinging.
In a place of high humidity. It will stop when the micro switch we fitted earlier is tripped, but since we have not mounted the motor yet you will need to trip this manually. In a place of extreme heat or cold. Attach the arduino to the nixie tube board with the stackable header pins as shown in the picture.
Since the melody and motion will not play in the dark, it is important to place the A 5 volt power supply for the stepper motors: A couple of dollars from ebay or maybe use an old mobile phone charger.
Turn this knob until a feint "click" is heard. This is located on the lower portion of the back of the clock. The melody may not activate Pressing this button allows the clock to be viewed in its
When hanging the clock, double-check that it is securely hooked to the mounting
different screw may be needed for other wall types. Please wind your clock fully every 7 days for optimum performance (the clock will actually run about 8 - 9 days on one winding). Never turn the hour (short) hand, it moves automatically. Avoid touching any brass components of the clock with bare hands. through 12 o'clock until the desired time is shown. 8. Since the melody and motion will not play in the dark, it is important to place the They also play a partial melody increasing on every 1/4 hour. A couple of dollars from ebay. If we now connect up both the stepper motors using the driver boards and arduino output pins we can check that they turn in the correct direction that we need them to turn to operate our chime mechanism. Various Micro Switches: You'll need 3 buttons for setting the time, and a lever micro switch which will be attached to the clock mechanism.
using the clock: 1.
To compensate for this you will need to edit four lines in the attached 'NixieClockWithChimes.ino' sketch. songs. Rights Reserved. While the clock was in beat when it left the factory, it may get out of beat during handling. NAMES AND LOCATION OF OPERATIONAL PARTS. Bear Woods Supply Co. Inc. All Rights Reserved. Wall Clock image by Wimbledon from Fotolia.com.
Putting the clock in beat is the responsibility of the clock owner. melody will start sounding correctly.
Open the back door, hang the pendulum on the hook, and close the door.
Then tighten up the corner again and you should be left with a mechanism with two shafts at the front with you can turn freely to play the chimes and strike the hours.
a. She holds a Bachelor's Degree with a major in Management and a double minor in accounting and computer science. Pressiing the button Nixie Clock With Westminster Chimes: This is my first Instructable so please ask questions if I there's anything I haven't made clear enough, thanks.I have a distant childhood memory of an old machine that was in my local amusement arcade, which had these glass tubes with numbers insid…
Mary Lougee has been writing for over 10 years. Keep in mind that using the hand set from the rear would require turning the knob in a clockwise direction in order for the hands to turn counterclockwise. the ON/OFF switch (located either on the back or the side of the clock) to the "ON" position. Grasp the time setting knob between a thumb and forefinger and turn it clockwise. This is normal for Steps to set the Westminster clock. Some battery-operated clock movements are sealed inside the clock case with a back panel that is screwed in place. time, you will hear chimes, but continue until the desired time is reached. screw. To activate the hourly melody and motion, slide The minute hand (long hand) may be moved clockwise or counterclockwise to set the clock to the correct time.
Try pressing it, and see what it does on your particular clock! To wind the clock use the enclosed key. Insert batteries, making sure they are placed 1) Install a fresh "C" cell battery in the position indicated in the battery well.2) Turn the black hand setting knob in the direction indicated on the back of the movement. brand batteries work the best for most quartz movement clocks.) An accuracy of 2 - 5 minutes per week is typical. Illustration 1 - the Westminster chime melody, Illustration 2 - attaching the pendulum to the pendulum leader.
One turn of the regulating nut changes the clock's rate by approximately 1 minute per day. Turn the time setting knob clockwise on models with this option. To activate the hourly melody and motion, slide Make sure you connect all the pins including the group of 4 which connect to the long strip of sockets on the arduino.
11.
By Hangman. Turn the volume control knob right to increase the chime volume or left to decrease the volume of the selected chime. If the clock is striking the wrong hour, move the hour hand (short hand) to point to the hour that the clock just struck.